White four-pleat gathering tape 25 mm | Decoration

White curtain gathering tape – 25 mm – four pleats

Product description

This white gathering tape is 25 mm high and suitable for making curtains with a decorative four-pleat heading. Pulling the drawcords forms the fabric into evenly distributed groups of four pleats. This gives the curtain a fuller and more classic appearance than a simple gathered heading. The tape is easy to work with and is sewn to the reverse of the curtain fabric along the upper edge. After sewing, gently pull the cords until the curtain reaches the required width. Distribute the groups of pleats evenly across the complete width and tie the cords securely. It is best not to cut the cords too short. Roll them up and conceal them behind the curtain instead. This allows you to adjust the width later or release the pleats when the curtain needs cleaning. The gathering tape has an approximate fullness ratio of 1:2.5. For a curtain with a finished width of approximately 1 metre, you will therefore need around 2.5 metres of curtain fabric and 2.5 metres of gathering tape, excluding the required hemming and processing allowance.

Product: curtain gathering or pleating tape
Colour: white
Height: 25 mm
Type: sew-on
Features: drawcords
Pleat style: groups of four pleats
Fullness ratio: approximately 1:2.5
Application: curtains with full and evenly distributed groups of four pleats
Sold by: the metre, orderable to the nearest centimetre
Price: per metre

Sewing instructions

First determine the required finished height and width of the curtain. When calculating the fabric quantity, allow for an approximate fullness ratio of 1:2.5. For 1 metre of finished curtain width, you will therefore need approximately 2.5 metres of fabric and 2.5 metres of gathering tape. Add the required fabric for the side and bottom hems and a small processing allowance. Pin or tack the gathering tape horizontally to the reverse of the curtain fabric along the upper edge. Check that the tape is positioned at the same height across the complete width. Make sure the drawcords remain accessible at both ends and do not stitch through them. Sew the tape securely along its upper and lower edges using a thread suitable for the curtain fabric. Tie the drawcords securely at one end and then pull them evenly from the other end. Gently gather the curtain to the required width. Carefully distribute the groups of four pleats across the complete width to create a balanced curtain heading. Tie the cords securely after distributing the pleats. Roll up the remaining ends and conceal them neatly behind the curtain. Only cut the cords if you are certain that the width will not need to be adjusted later. Even then, leave enough cord to secure the knot properly. If in doubt, make a test piece first. This allows you to check whether the needle, thread, stitch length and sewing-machine tension are suitable for the combination of gathering tape and curtain fabric.

ORDERING INFORMATION

You can order this product to the nearest centimetre. The stated price is per metre.

HOW TO ORDER

Quantity: enter the number of separate pieces you require.
Length: enter the required length per piece. The entered length applies to each separate piece. For example, would you like 2 pieces measuring 1.50 metres each? Enter 2 under Quantity and 1.50 m under Length. You will receive two separate pieces measuring 1.50 metres each. The total ordered length in this example is 3 metres.

FIXED WIDTH AND CONTINUOUS LENGTH

This product is supplied in a fixed width. The width is stated in the product specifications. Before ordering, check that the fixed width is suitable for your application. Would you like one continuous piece measuring, for example, 3 metres? Enter 1 under Quantity and 3.00 m under Length. You will receive one continuous 3-metre piece, subject to the available roll length. Do you require several pieces in different lengths? Add them as separate order lines or contact us before ordering.

REQUESTING A SAMPLE

If a sample is available for this product and you would first like to assess its colour, texture, quality or thickness, enter 1 under Quantity and 0.10 m under Length. You will receive a 10-centimetre sample across the product’s fixed width.

CUSTOM-CUT PRODUCTS AND RETURNS

This product is cut specially to the length you enter. Cut or made-to-measure products cannot therefore be returned. Before ordering, carefully check the number of pieces required, the desired length per piece, the fixed width, the intended application, any pattern repeat and the necessary cutting or processing allowance. Do you have questions about the correct size or application? Please contact us before ordering. We will be happy to advise you.

Frequently asked questions

1. What is meant by four pleats?

Pulling the drawcords forms the curtain fabric into evenly distributed groups of four pleats. This gives the curtain a full and decorative finish.

2. How high is the gathering tape?

The gathering tape has a fixed height of 25 mm.

3. How much fabric and gathering tape do I need?

The approximate fullness ratio is 1:2.5. For a finished curtain width of around 1 metre, you will need approximately 2.5 metres of fabric and 2.5 metres of gathering tape. Remember to add the required hemming and processing allowance.

4. How is the gathering tape attached?

The tape is sewn horizontally to the reverse of the curtain fabric along the upper edge. Make sure you do not stitch through the drawcords.

5. Is the gathering tape sold by the metre?

Yes. The stated price is per metre, and you can order the required length to the nearest centimetre.